AXBB-E Ethernet Motion Controller And Breakout Board Combined Controller

AXBB-E Ethernet Motion Controller And Breakout Board Combined Controller

SKU: CND-003

Combine Ethernet Motion Controller and Breakout Board in a single module. Can control up to 6-axes with Mach3, Mach4 or UCCNC software with onboard I/Os. Up to 400kHz step frequency. The controller can be connected to an additional Breakout Board to extend the number of I/Os. 

Note: The AXBB-E requires 2x power supplies - 1x 5VDC and 1x 12-24VDC. 

CNCDrive
  • Manufacturer: CNCDrive
Buy more for less:
1-4items$189.18/ each 
5-9items$170.26/ eachsave10%
10or more items$160.80/ eachsave15%
  • $189.18
Qty:  
In stock(2 items available)

The AXBB-E is an Ethernet Motion Controller and Breakout Board combination module. It can communicate with a computer via Ethernet direct connection or via a router or network switch.

The controller can be used to control machine tools with stepper or servo motor controls using step and direction signals and has a maximum stepping frequency of 400kHz. The controller can control up to 6 axes. Althought there are only 8 dedicated step and directions signals wired out on the board (which supports up to 4 axes), the I/Os on the software side are freely configurable to any pins - making it possible to use all 6 axes if required. 

For the I/Os, the controller includes:

  • 8x non-isolated outputs to be used as step and direction signals.
  • 8x isolated outputs to drive relays, laser controller or any device that require isolation. 24VDC capable
  • 6x isolated inputs for sensors, switches and pushbuttons. 24VDC capable.
  • 1x safety charge pump circuit with isolated output.
  • 2x analog input channels which can work with externally connected potentiometer (recommended full scale resistance 1k - 10kΩ). These signals can be used to control feedrate override and spindle speed ovveride in the software. 
  • 1x analog output channel with 0-5V or 0-10V (jumper selectable). This signal can be used to control speed of spindle motor with a VFD
  • 1x IDC26 female port which can be used to connect additional Parallel Port compatible breakout board to extend the number of I/Os. 

Important: The AXBB-E requires 2x power supplies:

  • 1x 5VDC (at least 500mA) digital power supply for internal logic, the non-isolated I/Os, analog ports and IDC26 extention port
  • 1x 12-24VDC power supply for external devices and components connected to isolated I/Os.
  • 2x Power supplies: 5V 500mA + 12-24V.
  • Isolated I/Os are 24VDC capable. 
  • 8x optically isolated high speed N-channel power mosfet transistor outputs. Maximum 500mA at 10Mbit/s.
  • 9x non-isolated buffered TTL outputs for step/dir signals, laser driver etc. Maximum 20mA with 0/5V voltage level.
  • 6 high speed optoisolator inputs. Accepts 10-30V input with internal series 2.2kΩ resistor. Max speed 10Mbit/s.
  • Isolated charge pump output with power N-channel mosfet transistor.
  • 1 IDC26 non-isolated extension port with standard Parallel Port pinout (12 outputs and 5 inputs).
  • LED indicators.
    • SKU
      CND-003
    • Weight
      0.2 kg

Faulty Goods and Warranty

Where such goods have been supplied we undertake to repair or replace them as quickly as possible.Prior to returning faulty items, please contact us with a description of the fault as one of our engineers might be able to assist you by resolving the issue over the phone.
A Warranty form must be filled out and returned with any goods.

Our standard warranty period is 12 months from the date of purchase unless stated otherwise.

Other warranty periods:

Labjack Products: 5 Years
Atop Products: 3 Years
MeanWell Products: 3 Years
Terracom Products: 3 Years

Warranty is subject to us being satisfied that a defect was caused by defective workmanship or materials and was not caused by or was not substantially contributed to by other factors beyond our control including incorrect installation, alterations or modifications of the product not recommended by the manufacturer.

Returns Policy

If you are dissatisfied with our goods you may return them within 14 days of the dispatch date. Contact us for an authorisation and we will refund your purchase less shipping costs and restocking fees. All returned goods MUST be in AS NEW condition including ALL PACKAGING and DOCUMENTATION / MANUALS etc.

Please note:

  • The product returned will attract a 20% restocking fee.
  • The customer must pay the delivery costs.
  • Non standard, custom made or a specially manufactured or imported products are not returnable.
  • Semiconductors, books and software are not refundable

Full Terms and Conditions

By placing an order with Ocean Controls, you agree to be bound by our Terms and Conditions of Trade.

Related products

Customers who viewed this product also bought