IO Modules Modbus RTU

Modbus TCP/IP  weather station gateway with 8 x 4-20mA analog re-transmission channels.

MV110-24.16DN has 16 digital inputs on board which are implemented as switch contacts, NPN or PNP. In addition, the MV110-24.16DN version has galvanically isolated inputs in groups of 4. 

Digital output module MU110-24.16K has 16 digital outputs (NPN). The max. current load is 400 mA at 60 V DC. 

Digital output module MU110-24.16R has 16 digital outputs (relay). The max. current load is 3 A at 250 V AC or 30 V DC. The outputs are galvanically isolated in groups of 4. 

The analog output module MU110-24.6U has 6 analog outputs (0-10V). The available voltage value at the outputs is 10...36 V DC.  

MV110-24.8AS has 8 analog inputs (0-10 V, 0-5 mA, 0(4)-20 mA). The module requires 24 V DC power supply and supports Modbus RTU/ASCII communication via a serial RS485 interface.  

The analog output module MU110-24.8I has 8 analog outputs (4-20 mA). The available voltage value at the outputs is 10 to 36 V DC.

The MK110-24.8D.4R Digital I/O-Module has 8 digital inputs and 4 relay outputs

Digital output module MU110-24.8K has 8 digital outputs (NPN). The max. current load is 400 mA at 60 V DC. 

Digital output module MU110-24.8R has 8 digital outputs (relay). The max. current load is 4 A at 250 V AC or 24 V DC. The outputs are galvanically isolated in groups of 4. 

The analog input module MV110-24.8A has 8 analog inputs which can be connected to various types of RTDs, thermocouples, position encoders and standard signals.

The module MU110-24.1TD is a 1-channel input module for resistor bridges (strain gauge or load cell). Requires 24 V DC power supply and supports Modbus RTU/ASCII communication via a serial RS485 interface.

The CS2RS-D507 is a Modbus (RS485) control closed loop stepper driver, able to power 2 phase stepper motors smoothly with very low motor heating & noise. It can provide up to 7.0 A, operating at 20-50 VDC.

The EM2RS-556 is a Modbus (RS485) control open loop stepper driver, able to power 2 phase stepper motors smoothly with very low motor heating & noise. It can provide up to 5.6 A, operating at 20-50 VDC.

Emko Elektronik Proop I/O module features 8 Digital Inputs, 8 Transistor Outputs, 5 Analog Inputs 4-20mA and 2 Analog Outputs 4-20mA. 24 V DC power supply and supports Modbus RTU communication via a serial RS485 interface.  

PC or PLC based 6.5-36 VDC I/O Module 4DI+8DO+3AI via Modbus protocol.

KTA-224 can now be powered 6.5-36 VDC, therefore KTB-224 has been discontinued.

USB and RS-485 Modbus IO slave with 8 relays and 8 analog inputs. 8~28V version.

KTA-226 can now be powered 8-28VDC, therefore KTB-226 has been discountinued.

Light and temperature sensor with voltage and current retransmission, and dual independent open-collector outputs for alarms. RS-485 Modbus Communication.

OD-PULSE12 meter pulse counter modules are designed to count pulses from meters such as energy, gas, water and heat meters. Twelve 32bit counters. Outputs Modbus RTU over RS-485.

The KTA-399 is a 3 Channels counter module with non-volatile memory. Counts at up to 1kHz with 32-bit counting registers. Outputs Modbus RTU over RS-485.

Modbus RTU I/O Module with DIN-rail Enclosure. Ideal for remote zoning applications. 2 x Analog 0-10V inputs , 4 x analogue 0-10V outputs, 2 x dedicated volt-free digital inputs. 2 x 24Vac triac outputs. 24Vac power supply.

MOD-IO9-AI is a Modbus RTU I/O Module with Wall Mounting Enclosure. Ideal for remote zoning applications. 

Modbus RTU I/O Module with Wall Mounting Enclosure. Ideal for remote zoning applications.

Modbus RTU I/O Module with DIN Rail Mounting Enclosure. Ideal for remote zoning applications.