- Computer Products
- Data Acquisition
- Data Loggers
- Electrical Switches
- Electrical Terminals-Wiring
- Industrial IoT
- Large Displays
- Modbus-Bacnet-MBus Products
- Motor Drivers & Controllers
- Motors & Accessories
- Panel Meters
- PLCs & HMIs
- Power Supplies
- Relays & Relay Cards
- 1 Wire
- Capacitive Proximity
- Float Switches
- Hall Effect
- Inductive Proximity
- Length & Distance
- Light & Colour
- Limit & Foot Switches
- Liquid Level
- Load Cells
- PhotoElectric Switches
- Pressure Transducers
- Smartphone Based
- Temperature RTD and T/C
- Temperature Other
- Temperature & Humidity
- VOC - Air Quality
- Signal Conditioners
- Test Equipment
SKU: LAJ-002In stock (3 items available)
Screw terminal connections, with short-circuit and overvoltage protection, for the extra 16 digital I/O on the LabJack U12.
SKU: LAJ-003Available for backorder
Temperature sensor mounted in a plastic tube with a current limiting resistor. The probe is suitable for air, surface and non-corrosive liquids.
SKU: LAJ-006In stock (4 items available)
High-level linear voltage output and high accuracy. Operating temperature range from 0 to +150 °C.
SKU: LAJ-004In stock (1 item available)
Selectable digital gain at values of 1, 10, 100 and 1000. Four TTL or CMOS-compatible address lines individually selects the amplifier gains.
SKU: LAJ-005In stock (1 item available)
Two calibrated microsensors with serial digital output, which results in superior signal quality, a fast response time and insensitivity to external disturbances. Operating temperature range of -40 to 120 °C.
SKU: LAJ-014In stock (4 items available)
Provides convenient screw terminal access to 12 digital I/O available on a DB15 connector.
SKU: LAJ-030In stock (3 items available)
A signal conditioning module that divides 2 single-ended uni-polar channels of 0 to 10 V analog signals down to 0 to 2.5 V signals.
SKU: LAJ-031Available for backorder
Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7. On board switch allows 5 various gain settings, one of them being custom.
SKU: LAJ-032In stock (5 items available)
Allows 2 digital I/O lines on a U3, U6 and UE9 to each control a relay or other moderate load. Each has a switch to ground (i.e open-collector) that can hold off up to 50 V and can sink up to 200 mA.
SKU: LAJ-033In stock (3 items available)
8×8 grid of holes for prototyping custom signal-conditioning ticks.
SKU: LAJ-034In stock (2 items available)
A signal conditioning module designed to convert two 4 to 20 mA current loop signals into voltage signals that vary from 0.472 to 2.360 V.
SKU: LAJ-035In stock (2 items available)
LJTick-DAC is an analog output expansion module that provides a pair of 14-bit analog outputs with a range of ±10 V.
SKU: LAJ-012In stock (2 items available)
Plugs directly into the bottom of a LabJack U6, UE9 or T7 to give screw terminal access to extra IO signals.
SKU: LAJ-013In stock (1 item available)
Connects to the LabJack UE9's DB37 connector, providing convenient screw terminal access. Also provided is a solderless breadboard and useful power supplies.
SKU: LAJ-036Available for backorder
LJTick module that will convert two ±10 V signals to 0 to 2.5 V signals for LabJack U3, U6, UE9, T4 and t7
SKU: LAJ-039In stock (1 item available)
12 channel, semiconductor switch output module designed for Labjack U3, U6, UE9, T4 and t7 data acquisition modules. 750 mA per channel at 5 to 28 VDC.
SKU: LAJ-017Available for backorder
80 channel analog multiplexor for U6, UE9 and T7 Labjack data acquisition modules.
SKU: LAJ-018Available for backorder
Short, 37 pin cable suits the expansion plug on the LabJack U6, U6-Pro, UE9 and UE9-Pro.
SKU: LAJ-016In stock (1 item available)
Plugs directly into the bottom of a LabJack - U12 via the DB25 connector. The card doesn't come with relays loaded, it is a bare PCB that will accept either 16 miniature style relays or 8 standard size relays.
SKU: LAJ-024In stock (1 item available)
Is designed to plug directly into the bottom of a U3/U6/U9/T7 series via the DB15 connector, using the 12 EIO/CIO lines to control up to 12 I/O modules. Output or input types of digital I/O modules can be used. The card doesn't come with relays loaded, it is a bare PCB that will accept either 16 miniature style relays or 8 standard size relays.
SKU: LAJ-0311In stock (3 items available)
Dual high input impedance buffer for analog signals. Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7 Labjack Data Acquisition modules.
SKU: LAJ-040In stock (2 items available)
A signal conditioning module that divides 2 single-ended unipolar channels of 0 to 10 V analog signals down to 0 to 2.0 V signals.
SKU: LAJ-038In stock (1 item available)
DIN rail mount clip for LabJack U3/U6/UE9/T4/T7.
SKU: LAJ-0301In stock (2 items available)
The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.