- Clearance
- Arduino
- CNC
- Communications
- Computer Products
- Controllers
- Data Acquisition
- Data Loggers
- Electrical Switches
- Electrical Terminals-Wiring
- Enclosures
- Industrial IoT
- Large Displays
- Lighting
- Modbus-Bacnet-MBus Products
- Motor Drivers & Controllers
- Motors & Accessories
- Panel Meters
- PLCs & HMIs
- Power Supplies
- Prototyping
- Relays & Relay Cards
- Security
-
Sensors
- 1 Wire
- Accelerometers
- Capacitive Proximity
- Chemical
- Compass
- Current-Voltage
- Float Switches
- Flow
- Gas
- Hall Effect
- Inclinometers
- Inductive Proximity
- Length & Distance
- Light & Colour
- Limit & Foot Switches
- Liquid Level
- Load Cells
- PhotoElectric Switches
- Pressure Transducers
- Smartphone Based
- Temperature RTD and T/C
- Temperature Other
- Temperature & Humidity
- Ultrasonic
- VOC - Air Quality
- Signal Conditioners
- Software
- Test Equipment
- Timers
- Weather
LabJack Accessories
Sort by:
Price Low - High
-
-
-
LJTick-RelayDriver (LJTRD)
SKU: LAJ-032Allows 2 digital I/O lines on a U3, U6 and UE9 to each control a relay or other moderate load. Each has a switch to ground (i.e open-collector) that can hold off up to 50 V and can sink up to 200 mA.
-
LJTick-DigitalOut5V
SKU: LAJ-0321Converts 3.3V digital outputs to 5V digital outputs on a U3, U6, UE9, T4 and T7 Labjack DAQ modules . Easily control 5V relays, or interface with a 5V logic device.
-
LJTick-OutBuff
SKU: LAJ-0352The LJTick-OutBuff (LJTIB) is an output buffer tick that increases the output current of the DAC outputs on LabJack devices. Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7.
-
LJTick VRef2.5V
SKU: LAJ-0305The LJTick-VRef is a Voltage reference accessory that outputs a stable 2.5V signal. Can be used with the Labjack U3, U6, UE9, T4 and T7 data acquisition modules
-
LJTick VRef4.1V
SKU: LAJ-0306The LJTick-VRef is a Voltage reference accessory that outputs a stable 4.096V signal. Can be used with the Labjack U3, U6, UE9, T4 and T7 data acquisition modules
-
3ft DC-37 M/F Serial Cable
SKU: LAJ-018Short, 37 pin cable suits the expansion plug on the LabJack U6, U6-Pro, UE9 and UE9-Pro.
-
LJTick-Divider (LJTD)
SKU: LAJ-030A signal conditioning module that divides 2 single-ended uni-polar channels of 0 to 10 V analog signals down to 0 to 2.5 V signals.
-
LJTick-Resistance 1K
SKU: LAJ-0301The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.
-
LJTick-Resistance 10K
SKU: LAJ-0302The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.
-
LJTick-Resistance 100K
SKU: LAJ-0303The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.
-
LJTick-Divider (DIV-5)
SKU: LAJ-040A signal conditioning module that divides 2 single-ended unipolar channels of 0 to 10 V analog signals down to 0 to 2.0 V signals.
-
CB15 - LabJack Terminal Board
SKU: LAJ-014Provides convenient screw terminal access to 12 digital I/O available on a DB15 connector.
-
LJTick-Level Shifter
SKU: LAJ-036LJTick module that will convert two ±10 V signals to 0 to 2.5 V signals for LabJack U3, U6, UE9, T4 and t7
-
LJTick-InBuff
SKU: LAJ-0311Dual high input impedance buffer for analog signals. Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7 Labjack Data Acquisition modules.
-
LJTick-CurrentShunt
SKU: LAJ-034A signal conditioning module designed to convert two 4 to 20 mA current loop signals into voltage signals that vary from 0.472 to 2.360 V.
-
CB25 - Labjack Terminal Board for Digital I/O
SKU: LAJ-002Screw terminal connections, with short-circuit and overvoltage protection, for the extra 16 digital I/O on the LabJack U12.
-
CB37 - LabJack UE9 Terminal Board
SKU: LAJ-012Plugs directly into the bottom of a LabJack U6, UE9 or T7 to give screw terminal access to extra IO signals.
-
Digital Temperature/Humidity Probe
SKU: LAJ-005Two calibrated microsensors with serial digital output, which results in superior signal quality, a fast response time and insensitivity to external disturbances. Operating temperature range of -40 to 120 °C.
Labjack have discontinued this product because chip set is no longer available
-
LJTick-InAmp
SKU: LAJ-031Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7. On board switch allows 5 various gain settings, one of them being custom.
-
Stainless Steel Temperature Probe
SKU: LAJ-006High-level linear voltage output and high accuracy. Operating temperature range from 0 to +150 °C.
-
LJTick-Dac - Digital to Analog Converter
SKU: LAJ-035LJTick-DAC is an analog output expansion module that provides a pair of 14-bit analog outputs with a range of ±10 V.
-
PS12DC Power Switching Board
SKU: LAJ-03912 channel, semiconductor switch output module designed for Labjack U3, U6, UE9, T4 and t7 data acquisition modules. 750 mA per channel at 5 to 28 VDC.