LabJack Accessories

Screw terminal connections, with short-circuit and overvoltage protection, for the extra 16 digital I/O on the LabJack U12.

Selectable digital gain at values of 1, 10, 100 and 1000. Four TTL or CMOS-compatible address lines individually selects the amplifier gains.

Two calibrated microsensors with serial digital output, which results in superior signal quality, a fast response time and insensitivity to external disturbances. Operating temperature range of -40 to 120 °C.

Labjack have discontinued this product because chip set is no longer available

High-level linear voltage output and high accuracy. Operating temperature range from 0 to +150 °C.

Plugs directly into the bottom of a LabJack U6, UE9 or T7 to give screw terminal access to extra IO signals.

Connects to the LabJack UE9's DB37 connector, providing convenient screw terminal access. Also provided is a solderless breadboard and useful power supplies.

Provides convenient screw terminal access to 12 digital I/O available on a DB15 connector.

Plugs directly into the bottom of a LabJack - U12 via the DB25 connector. The card doesn't come with relays loaded, it is a bare PCB that will accept either 16 miniature style relays or 8 standard size relays.

80 channel analog multiplexor for U6, UE9 and T7 Labjack data acquisition modules.

Short, 37 pin cable suits the expansion plug on the LabJack U6, U6-Pro, UE9 and UE9-Pro.

Is designed to plug directly into the bottom of a U3/U6/U9/T7 series via the DB15 connector, using the 12 EIO/CIO lines to control up to 12 I/O modules. Output or input types of digital I/O modules can be used. The card doesn't come with relays loaded, it is a bare PCB that will accept either 16 miniature style relays or 8 standard size relays.

A signal conditioning module that divides 2 single-ended uni-polar channels of 0 to 10 V analog signals down to 0 to 2.5 V signals.

The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.

The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.

The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.

The LJTick-VRef is a Voltage reference accessory that outputs a stable 2.5V signal. Can be used with the Labjack U3, U6, UE9, T4 and T7 data acquisition modules

The LJTick-VRef is a Voltage reference accessory that outputs a stable 4.096V signal. Can be used with the Labjack U3, U6, UE9, T4 and T7 data acquisition modules

Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7. On board switch allows 5 various gain settings, one of them being custom.

Dual high input impedance buffer for analog signals. Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7 Labjack Data Acquisition modules.

Allows 2 digital I/O lines on a U3, U6 and UE9 to each control a relay or other moderate load. Each has a switch to ground (i.e open-collector) that can hold off up to 50 V and can sink up to 200 mA.

Converts 3.3V digital outputs to 5V digital outputs on a U3, U6, UE9, T4 and T7 Labjack DAQ modules . Easily control 5V relays, or interface with a 5V logic device.

8×8 grid of holes for prototyping custom signal-conditioning ticks.

A signal conditioning module designed to convert two 4 to 20 mA current loop signals into voltage signals that vary from 0.472 to 2.360 V.

LJTick-DAC is an analog output expansion module that provides a pair of 14-bit analog outputs with a range of ±10 V.