Heating Cooling Controller With BACnet MS/TP Communication DIN Rail Mount

Heating Cooling Controller With BACnet MS/TP Communication DIN Rail Mount

SKU: SXS-151

Multistage BACnet heating and cooling controller with DIN Rail mount. 3 analogue 0..10V outputs, 2 digital outputs, 1 external auto-detect sensor, 1 digital input, and input for external NTC10 Temperature Sensor.

NOT AVAILABLE FOR BACKORDER

Produal (Syxthsense)
    • % off
    $132.87 save $33.22
  • $99.65
Qty:  
In stock(2 items available)

The SRC-110-BAC BACnet series controllers have been designed for zone heating and cooling control and DIN-rail mounting. The controllers have 3 analogue 0..10Vdc outputs and two digital outputs that can be configured for heating and cooling control. The controllers can operate as Proportional Only or as Proportional + Integral Controllers. The controllers have built-in BACnet MS/TP communication for connection to BMS systems.

The controller can have up to 2 heating and cooling stages. The analogue outputs can be individually configured for any of the heating/cooling stages and digital outputs can be configured as 3-point, PWM (thermic) or On/Off control.

The controllers are connected to either TER-NTC10 room temperature sensor or TEKY-NTC10 flying lead sensor for temperature measurement. If room setpoint is required then TER-NTC10-SPR sensor can be used together with the SRC-110-BAC DIN-rail mounted BACnet room controllers.

The controller configuration parameters are adjusted thrrough the SW-DCT-USB tool. Rred and blue LEDs under the cover indicate the controller operation in heating or cooling mode and can be used for servicing the controllers.

The BACnet communication supports automatic device and point discovery making the controller configuration as a part of the BACnet system fast, simple and efficient.


  • Configurable Room and Zone Controllers with DIN-rail Mounting
  • Up to 2 Heating and up to 2 Cooling stages
  • Digital Input for Night Mode or Cooling Disable Override
  • Address and Baud Rate Setting via Bit switch or via the Configuration Software
  • Red and blue LEDs under the cover indicate if the temperature is below or above the setpoint
  • Configuration is done via SW-DCT-USB Windows based configuration tool
  • Plug-In Wiring Terminals
  • Power supply: 24Vac/dc 
  • Outputs: 3 Analogue 0..10Vdc, Configurable to Any of the Stages
  • Outputs: 2 Digital 24Vac Triac, Configurable for On/Off, PWM (Thermic) and 3-Point Control
  • External NTC10 Temperature Sensor; such as TER-NTC10 or TEKY-NTC10
  • Remote User Setpoint via TER-NTC10-SPR Room Sensor
  • Protocol: BACnet MS/TP RS-485
  • Communication: 9k6/19k2/38k4/76k8 Baud; Parity None/Even/Odd, 1 or 2 Stop
  • Interface: RS485, maximum 63 devices
  • Addressing: 0..63 via a bit switch; 0..247 via tool / network
  • Temperature: 0°C...+50°C (32..122°F)
  • Humidity: 0...95%rh (non-cond.)
  • Standards CE: Conformity CE Directive 2004/108/EY EN61000-6-3: 2001 (Generic Emission) EN61000-6-1: 2001 (Generic Immunity)
  • Degree of Protection: IP20
  • Housing: ABS Plastics, Self Extinguishing
  • Dimensions: W106 x H97 x D38mm
    • SKU
      SXS-151
    • Weight
      0.3 kg
    • Dimensions (L x W x H)
      15 x 8.5 x 5.5 cm

Faulty Goods and Warranty

Where such goods have been supplied we undertake to repair or replace them as quickly as possible.Prior to returning faulty items, please contact us with a description of the fault as one of our engineers might be able to assist you by resolving the issue over the phone.
A Warranty form must be filled out and returned with any goods.

Our standard warranty period is 12 months from the date of purchase unless stated otherwise.

Other warranty periods:

Labjack Products: 5 Years
Atop Products: 3 Years
MeanWell Products: 3 Years
Terracom Products: 3 Years

Warranty is subject to us being satisfied that a defect was caused by defective workmanship or materials and was not caused by or was not substantially contributed to by other factors beyond our control including incorrect installation, alterations or modifications of the product not recommended by the manufacturer.

Returns Policy

If you are dissatisfied with our goods you may return them within 14 days of the dispatch date. Contact us for an authorisation and we will refund your purchase less shipping costs and restocking fees. All returned goods MUST be in AS NEW condition including ALL PACKAGING and DOCUMENTATION / MANUALS etc.

Please note:

  • The product returned will attract a 20% restocking fee.
  • The customer must pay the delivery costs.
  • Non standard, custom made or a specially manufactured or imported products are not returnable.
  • Semiconductors, books and software are not refundable

Full Terms and Conditions

By placing an order with Ocean Controls, you agree to be bound by our Terms and Conditions of Trade.

Related products