|

LabJack T7 Data Acquisition OEM Card

In stock (1 item available)
  • Weight
    0.5 kg
  • SKU
    LAJ-045O

OEM Card Version of LABJACK T7 Multifunction DAQ with Ethernet and USB.

Buy more for less:
Quantity ex GST incl GST Saving
1-4 items AUD660.30 / each AUD726.33 / each  
5-9 items AUD594.30 / each AUD653.73 / each save 10%
10 or more items AUD561.25 / each AUD617.38 / each save 15%
  • AUD660.30 ex GST
  • AUD726.33 incl GST
Qty:  

Labjack T7-OEM is a PCB-only version of the standatd T7. The enclosure, and most connectors are not installed on the OEM version, which allows customers to fit their own connectors themselves.

Features:

  • Expandable to 80 single ended or 40 differential with the Mux80 Card
  • Instrumentation Amplifier Inputs - software Programmable Gains of x1, x10, x100 and x1000
  • Built-In CJC Temperature Sensor for thermocouples
  • Supports SPI, I2C, and Asynchronous Serial Protocols (Master Only)
  • Supports Software or Hardware Timed Acquisition
  • USB 2.0/1.1 Full Speed Interface (no connector)
  • Examples Available for C/C++, VB, LabVIEW, Python in due cours

Power supply: Through USB Cable

Analog Inputs: 14 (16-18+ Bits Depending on Speed)

Digital I/O: 20

Analogue Input: Ranges ±10, ±1, ±0.1 and ±0.01 Volts

Fixed Current Outputs: 2 (200/10 uA)

Analogue Outputs: 2(12-Bit, 0-5 Volts)

Sampling rate: 50 kHz (Depending on resolution) 

Response time: Less than 1 Millisecond

Counters: Up to 10

Timers: Up to 8 (Pulse Timing, PWM Output, Quadrature Input, ...)

Communication interface: Ethernet RJ45

Operating temperature: Industrial Range -40 to +85 °C

Analog inputs: 

The LabJack T7 has 14 external analogue inputs (AIN0-AIN13). AIN0-AIN3 are available on screw terminals and also on the DB37 connector. All 14 analogue inputs are available on the DB37 connector. The Mux80 multiplexer can expand this to to 80 single ended or 40 differential channels.

The maximum input range is ±10 volts, with software selectable gains of x1, x10, x100 and x1000. Each analogue input can be measured single-ended, or differential in even/odd pairs

Command/response (software timed) analogue input reads typically take 1-4 ms depending on number of channels and communication configuration. Hardware timed input streaming has a maximum rate that varies with resolution from 4 ksamples/s at 18 bits to 50 ksamples/s at 16 bits

It is possible to connect thermocouples directly to the T7. The T7 has an internal temperature sensor, which can be used for cold junction compensation. DAQFactory contains thermocouple linearisation as a built-in conversion function.


For more information about the analog inputs see Section 15 and Appendix A of the User's Guide. For data rate information see Sections 3.1 and Sections 3.2. The User's Guide can be found on the T7 Support Page .

Analog outputs:

The LabJack T7 has 2 analog outputs (DAC0 and DAC1) that are available both on screw terminals and the DB37 connector. Each analog output can be set to a voltage between 0 and 4.9 volts with 12-bits of resolution. The analog outputs are based on a true voltage reference.

The analog outputs are updated in command/response mode, with a typical update time of 1.2-4.0 ms depending on communication configuration.

For more information about the analog outputs see Section 16 of the User's Guide on the Support Page

Digital I/Os:

The LabJack T7 has 23 digital I/O channels which can be individually configured as input, output-high, or output-low. 8 of these lines are called flexible digital I/O (FIO) and can be software configured as up to 6 timers and 2 counters.

The first 4 FIO are available on screw terminals and the DB37 connector. All 8 FIO and 3 MIO are available on the DB37 connector, and 8 EIO and 3 CIO are available on the DB15 connector.

Command/response (software timed) reads/writes typically take 1.2-4.0 ms depending on communication configuration. The digital inputs can also be read in a hardware timed input stream where up to 16 inputs count as a single stream channel.

For more information about the digital I/O see Section 14 and Appendix A of the User's Guide. The User's Guide can be found on the T7 Support Page .

Timers:

Up to 4 digital I/O can be configured as timers. The timers are very flexible, providing options such as PWM output, pulse timing, pulse counting, and quadrature input.

Counters: 

Up to 2 digital I/O can be configured as 32-bit counters. Since counting is one possible mode of the timers above, the T7 has up to 6 counting inputs

I/O Protection:

All I/O lines on the T7 are protected against minor overvoltages.

Power supply: 

Power can be provided by the USB cable or an external 5 volt supply (included). When only Ethernet is connected, and an isolated power supply is used (such as the included wall-wart), the entire T7 is electrically isolated.

High channel count application: 

By using USB hubs or Ethernet switches, many LabJacks can be interfaced to a single PC, providing an inexpensive solution for low-speed high channel count applications.

Modbus: 

Modbus is an industry standard command/response protocol for data acquisition and control equipment. The T7 supports Modbus/TCP in hardware, so any software that supports Modbus/TCP can talk to the T7 with no further software/drivers required. (More Info)

Satisfaction guaranteed: 

Everything we sell has a 30-day money back guarantee. If, for any reason, you are not satisfied with a product, contact us to arrange your choice of a refund or replacement. In addition, the LabJack T7 is covered by a 1-year limited warranty.

Technical support: 

All LabJacks include lifetime technical support. Support resources include forum, FAQs, email, and telephone.

Software, Drivers and Examples: 

DAQFactory is measurement and automation software from AzeoTech.  The free version, DAQFactory Express, supports the T7/U3/U6/UE9/U12. The Support Page has drivers and sample code. We have drivers for the three major operating systems, and examples for most common programming languages.

For More information: 

The User's Guide on T7 Support Page has all the specifics for working with the T7. You'll also find the quick start guides, and any other literature we've published on the T7.

LabJack's Modules Comparison Chart:

LabJack-Comparison-Chart.jpg


t7-dimensions.jpg

T7 - Dimensions in inches

Faulty Goods and Warranty

Where such goods have been supplied we undertake to repair or replace them as quickly as possible.Prior to returning faulty items, please contact us with a description of the fault as one of our engineers might be able to assist you by resolving the issue over the phone.
A Warranty form must be filled out and returned with any goods.

Our standard warranty period is 12 months from the date of purchase unless stated otherwise.

Other warranty periods:

Labjack Products: 5 Years
Atop Products: 3 Years
MeanWell Products: 3 Years
Terracom Products: 3 Years

Warranty is subject to us being satisfied that a defect was caused by defective workmanship or materials and was not caused by or was not substantially contributed to by other factors beyond our control including incorrect installation, alterations or modifications of the product not recommended by the manufacturer.

Returns Policy

If you are dissatisfied with our goods you may return them within 14 days of the dispatch date. Contact us for an authorisation and we will refund your purchase less shipping costs and restocking fees. All returned goods MUST be in AS NEW condition including ALL PACKAGING and DOCUMENTATION / MANUALS etc.

Please note:

  • The product returned will attract a 20% restocking fee.
  • The customer must pay the delivery costs.
  • Non standard, custom made or a specially manufactured or imported products are not returnable.
  • Semiconductors, books and software are not refundable

Full Terms and Conditions

By placing an order with Ocean Controls, you agree to be bound by our Terms and Conditions of Trade.

Customers who bought this product also bought

Drop items here to shop
Product has been added to your cart

Related products