24VDC PCB Power Relay. Able to switch 20A

Features: 

• These SPDT relays are type T90(JQX-15F)

10 Turn 5K Potentiometer
LAST UNITS!

Useful for extending RF signals to externally mounted antennas

Dual 250 Ohm, 0.1%, 1W resistors, suitable for converting 4 to 20 mA loops to 1 to 5V.

Dual 500 Ohm, 0.1%, 1W resistors, suitable for converting 4 to 20 mA loops to 2 to 10V

Dual 1K Ohm, 5%, 1W resistors for adapting 12V systems to Leadshine stepper motor drives

Dual 4K7 Ohm, 5%, 1W resistors for general purpose use

Dual 2K2 Ohm, 5%, 1W resistors for adapting 24V systems to Leadshine stepper motor drives

120 Ohm resistor and 0.1uF capacitor for back EMF suppression on AC loads

Dual 120 Ohm, 5%, 1W resistors for RS-485 bus termination or general purpose use

470 Ohm & 330 Ohm Resistive Divider, for stepping down a 24V DC supply to 10V. Useful as a feed voltage to a potentiometer for 0-10V control for VSD, etc.

7-8dbi 700-2700MHz Waterproof Antenna, 12mm Screw Mounting and 3m cable with SMA Male Connector.

698-960mhz 1710-2700mhz 2-3dbi Waterproof  4G Antenna adhesive bonding with 2m RG174 Cable and SMA male connector.

5dbi 698-2700MHz GSM 3G 4G Antenna Waterproof Outdoor Panel.  4G LTE Aerial with SMA male connector and Magnetic Base Omnidirectional Antenna

7-8dbi 698-2700MHz GSM 3G and 4G Antenna Waterproof Outdoor Panel. 4G LTE Omnidirectional Antenna with 1.5m Cable and SMA male connector

LMR240 Low Loss coaxial cable with SMA Male to SMA Female Connector

BRT 4-20MA-GEL is a DC 4-20mA Generator with 0-100% Percentage LED Display. Fitted with a panel-mounted Grey Knob to adjust the 4-20mA output level.

BRT 420LGPM  is a 2-wire DC 4-20mA Generator with 4-20mA or 0-100% Percentage LCD Display. Fitted with a panel-mounted Grey Knob to adjust the 4-20mA output level.

BRT VIG-D2 is a DC 4-20mA Generator with 4-20mA or 0-100% Percentage LED Display. Fitted with a panel-mounted Knob to adjust the 4-20mA output level. Modbus RTU connectivity

MOD-TC-2 Thermistor monitoring Relay is used to monitor PTC sensors embedded within motor windings. On resistance rise above 3.3 kΩ  the alarm output will trip.

Fema I4L is an isolated signal converter for load cell signals and millivolts. Provides +5 Vdc excitation voltage to power the load cell, and ‘sense’ function to compensate for excitation voltage variations. Accepts direct connection of 1, 2, 3 or up to 4 load cells (typical 350 Ohms load cells). We have a service to configure the I4L for you if you require it.

BAC-IO9 is a BACnet I/O Module with Wall Mounting Enclosure. Ideal for remote zoning applications. 2 x resistive inputs (up to 65kOhm). 2 x volt-free digital inputs. 3 x 0..10Vdc analogue outputs. 2 x 24Vac triac outputs. 24Vac power supply.

MOD-IO9 is a Modbus RTU I/O Module with Wall Mounting Enclosure. Ideal for remote zoning applications. 2 x resistive inputs (up to 65kOhm). 2 x volt-free digital inputs. 3 x 0..10Vdc analogue outputs. 2 x 24Vac triac outputs. 24Vac power supply.

11WRSTC pump seal leak monitor relay / water leak detection relay & thermistor monitoring relay features detection of water contamination of oil, detection of water leaks from pipes in buildings, isolated probe supply and LED indication, Also available Klixon version.