LabJack Accessories

Short, 37 pin cable suits the expansion plug on the LabJack U6, U6-Pro, UE9 and UE9-Pro.

Provides convenient screw terminal access to 12 digital I/O available on a DB15 connector.

Screw terminal connections, with short-circuit and overvoltage protection, for the extra 16 digital I/O on the LabJack U12.

Plugs directly into the bottom of a LabJack U6, UE9 or T7 to give screw terminal access to extra IO signals.

EI-1022 is a plastic temperature probe, with a linear output of 10 mV per degree K. Operating temperature range from -40 to +100 °C.

DIN rail mount clip for LabJack U3/U6/UE9/T4/T7.

The LJTick-VRef is a Voltage reference accessory that outputs a stable 2.5V signal. Can be used with the Labjack U3, U6, UE9, T4 and T7 data acquisition modules

The LJTick-VRef is a Voltage reference accessory that outputs a stable 4.096V signal. Can be used with the Labjack U3, U6, UE9, T4 and T7 data acquisition modules

A signal conditioning module designed to convert two 4 to 20 mA current loop signals into voltage signals that vary from 0.472 to 2.360 V.

LJTick-DAC is an analog output expansion module that provides a pair of 14-bit analog outputs with a range of ±10 V.

Converts 3.3V digital outputs to 5V digital outputs on a U3, U6, UE9, T4 and T7 Labjack DAQ modules . Easily control 5V relays, or interface with a 5V logic device.

A signal conditioning module that divides 2 single-ended unipolar channels of 0 to 10 V analog signals down to 0 to 2.0 V signals.

A signal conditioning module that divides 2 single-ended uni-polar channels of 0 to 25 V analog signals down to 0 to 2.5 V signals. V_output = V_input/4 

A signal conditioning module that divides 2 single-ended uni-polar channels of 0 to 10 V analog signals down to 0 to 2.5 V signals. V_output = V_input/4 

LJTick module that will convert two ±10 V signals to 0 to 2.5 V signals for LabJack U3, U6, UE9, T4 and T7

Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7. On board switch allows 5 various gain settings, one of them being custom.

Dual high input impedance buffer for analog signals. Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7 Labjack Data Acquisition modules.

The LJTick-OutBuff (LJTIB) is an output buffer tick that increases the output current of the DAC outputs on LabJack devices. Plugs directly into the standard screw terminal block found on newer U3/U6/UE9/T4/T7.

8×8 grid of holes for prototyping custom signal-conditioning ticks.

Allows 2 digital I/O lines on a U3, U6 and UE9 to each control a relay or other moderate load. Each has a switch to ground (i.e open-collector) that can hold off up to 50 V and can sink up to 200 mA.

The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.

The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.

The LJTick-Resistance (LJT-Rx) makes it easy for LabJack devices to measure resistive sensors.

80 channel analog multiplexor for U6, UE9 and T7 Labjack data acquisition modules.