iEM-RS2323  2.3 N·m NEMA 23 Integrated Stepper Motor with Modbus

iEM-RS2323 2.3 N·m NEMA 23 Integrated Stepper Motor with Modbus

SKU: SMC-1303

iEM-RS Series is an integrated stepper motor with drive, and based on standard Modbus RTU protocol. Using RS485 communication it can network up to 31 axes. Its built-in PR feature with 16-segment position table (PR Mode) can save additional controllers in most of point-to-point applications, to greatly enhance system reliability and reduce the cost

Leadshine
  • Manufacturer: Leadshine
Buy more for less:
1-4items$137.90/ each 
5-9items$124.11/ eachsave10%
10or more items$117.21/ eachsave15%
  • $137.90
Qty:  
In stock(2 items available)

Leadshine iEM-RS2323 integrated stepper is a NEMA 23 stepper motor integrated with an advanced DSP stepper drive. It is based on standard Modbus RTU protocol. Using RS485 communications it can network up to 31 axes. Its built-in PR feature with 16-segment position table (PR Mode) can save additional controllers in most of point-to-point applications, to greatly enhance system reliability and reduce the cost. The iEM-RS2323 can be operated from a HMI or PLC using Modbus commands or it can be programmed and controlled by its digital I/O

Features

● NEMA23, 2.3N.m (Also available with Holding Torque 0.6, 0.8 and 1.3 Nm)

● Low noise and vibration, smooth motion

● Support Modbus RTU protocol, Internal 16-segment position commands

● Motion can be started by external I/O or RS485 or HMI 

● Support operation modes: Profile Position, Profile Velocity, Homing 

● 7 configurable digital inputs, 3 optically isolated digital outputs 

● RS232 port for tuning software connection, RS485 port for motion control 

● Over voltage, over current, etc. protections

Leadshine have the modbus stepper drive series EM2RS which are very similar in operation to the iEM-RS integrated drive. The following features in this video are the same as in the iEM-RS series.

Leadshine already loads default current-loop parameters for the iEM-RS2323 Those default parameter values have been optimized. They should be good enough for most industrial applications, and there is no need to tune them. However, if you want to fine tune the iEM-RS2323 for best performance for your applications, Leadshine also offers tuning software, ProTuner, which allows you to adjust those current-loop parameters. The serial cable for tuning is on our website at Serial Cable for iST and iES drives 


    • SKU
      SMC-1303
    • Weight
      1.6 kg
    • Dimensions (L x W x H)
      15 x 8 x 8 cm

IModel: iEM-RS2323

Series: iEM-RS

Frame Size: Nema 23

Command Source: Modbus RTU

Holding torque: 2.3 Nm

Digital Inputs: 3

Digital Outputs: 1

Input Logical Voltage: 12-24VDC

Operating environment: 

  • Environment: Avoid dust, oil fog and corrosive gases.
  • Ambient temperature: 0 to 50°C
  • Humidity: 40 to 90% RH

Storage temperature: -20 to 65°C

Length of motor + drive: 99 mm

Shaft Dia: 8mm

Weight: 1.4 Kg

Faulty Goods and Warranty

Where such goods have been supplied we undertake to repair or replace them as quickly as possible.Prior to returning faulty items, please contact us with a description of the fault as one of our engineers might be able to assist you by resolving the issue over the phone.
A Warranty form must be filled out and returned with any goods.

Our standard warranty period is 12 months from the date of purchase unless stated otherwise.

Other warranty periods:

Labjack Products: 5 Years
Atop Products: 3 Years
MeanWell Products: 3 Years
Terracom Products: 3 Years

Warranty is subject to us being satisfied that a defect was caused by defective workmanship or materials and was not caused by or was not substantially contributed to by other factors beyond our control including incorrect installation, alterations or modifications of the product not recommended by the manufacturer.

Returns Policy

If you are dissatisfied with our goods you may return them within 14 days of the dispatch date. Contact us for an authorisation and we will refund your purchase less shipping costs and restocking fees. All returned goods MUST be in AS NEW condition including ALL PACKAGING and DOCUMENTATION / MANUALS etc.

Please note:

  • The product returned will attract a 20% restocking fee.
  • The customer must pay the delivery costs.
  • Non standard, custom made or a specially manufactured or imported products are not returnable.
  • Semiconductors, books and software are not refundable

Full Terms and Conditions

By placing an order with Ocean Controls, you agree to be bound by our Terms and Conditions of Trade.

Related products

Customers who viewed this product also bought