CS-D508 8A 2 Phase CS Series Closed Loop Stepper Drive
Leadshine CS-D508 is a stepper motor driver with encoder feedback input. Operating at 20-50VDC, max 8A output current. Suits 2-phase CS Series Closed Loop Stepper Motors.
NOTE: When powering with 12VCC or 24VCC, the controller requires external resistors in series to it's terminals (refer to hardware manual).
Leadshine CS-D508 is a closed-loop stepper drive that, when implemented along with a compatible 2-phase stepper motor in NEMA frame sizes 17, 23, or 24, features a 1000-line incremental encoder. It can close the position loop between the motor and drive and, therefore, eliminate the loss-of-step problem in an open loop system. The CS-D508 implements an advanced control algorithm based on Leadshine's decades of experience in stepper and servo controls. It is ideal for upgrading open-loop stepper systems or replacing servo systems in some low to middle-speed applications.
Compared with an open loop stepper system, a CS-D508 adopted closed loop stepper system can eliminate loss of step, make real-time position error correction, and use 100% available torque of the driven stepper motor. It can also power the driven stepper motor with reduced heating, lower noise, and lower vibration.
When compared with a servo system, a CS-D508 adopted closed-loop stepper system can have much higher low-to-middle-speed torque. Such a control system also has the advantages of no tuning, no hunting, no overshooting, and much lower cost.
Features:
The main advantages over traditional servo and open-loop stepper systems are:
- Step & direction or CW/CCW control modes
- Powering a 2-phase stepper motor of NEMA 23, 24, or 34 with a 1000-line encoder
- Closed-loop eliminates loss of steps
- No Tuning, hunting, overshooting, or torque margin
- Reduced motor heating and more efficient
- Smooth motion and super-low motor noise
- CE certified and RoHS compliant
That closed stepper system can be used to upgrade open-loop stepper systems or replace some servo systems, especially in many small to medium speed applications such as CNC routers, CNC mills, CNC laser cutters, CNC plasmas, lab automation instruments, plotters, medical equipment, electronic equipment, small packaging machines, etc.
NOTE: When powered with 12VCC or 24VCC, the controller requires external resistors in series to its terminals (refer to the hardware manual).
Supply voltage: 20 to 50 VDC
Output current: 0.5 to 8 A
Logic signal current: 7 to 16 mA
Pulse input frequency: 200 kHz
minimal pulse width: 2.5 µs
Minimal direction setup: 5.0 µs
Isolation resistance: 500 MΩ
Operating environment:
- Environment: Avoid dust, oil fog, and corrosive gases
- Ambient temperature: 0 to 65 °C
- Humidity: 40 to 90% RH
- Operating temperature: 0 to 50 °C
- Vibration: 10 to 50 Hz / 0.15 mm
Storage temperature: -20 to 65 °C
Weight: Approx. 280 g
Dimension: 116 x 69 x 27 mm
Programming Cable:
The drive can be tuned with the ProTuner software and an LSK-001 (RJ-12 to DE-9 serial cable). Please note that a USB-to-RS232 converter using an FTDI chipset is recommended, such as the ZTC-005.
Cables:
To connect this driver to a matching Easy Servo motor, you'll also want power and encoder extension cables.
3 meters | 5 meters | 8 meters | 10 meters | |
|---|---|---|---|---|
Power | - | |||
Encoder | - |
Dispatch
In-stock orders are dispatched within 2 business days.
Shipping options
We deliver across Australia and internationally by any of the following methods:
- Australia Post Express
- Australia Post Parcel Post
- DHL
- FedEx (only international)
- Freight account. We'll email packaging dimensions when the shipment is ready to be book.
*Transit times vary depending on the shipping method and destination.
Store Pickup - Carrum Downs, Victoria, 3201
Order before 11am to collect after 2pm the same day. Mon–Fri, 9am–5pm, excludes public holidays.
RETURNS
How to return an item Contact us before sending anything back. Email info@oceancontrols.com.au or call +61 3 9708 2390. We'll confirm eligibility and guide you to the return process.
Return window 14 days from dispatch date.
Condition required Items must be unused and in original packaging, including all documentation and manuals.
Restocking fee A 20% restocking fee applies to all accepted returns. Return shipping costs are the customer's responsibility.
Non-returnable items
- Custom-made or specially imported products
- Software licences (some software have trial versions available)
- Items not in original, as-new condition
WARRANTY
How to make a warranty claim Before returning anything, please contact us. Our engineers can often resolve the issue remotely. If a return is required, our team will provide you with a warranty form to include with the goods.
What's covered Defects in materials and workmanship under normal use and correct installation.
What's not covered The warranty does not cover damage or failures caused by factors outside our control, including incorrect installation, unauthorised alterations or modifications, or any installation or use not recommended by the manufacturer.
Standard warranty All products carry a 12-month warranty from the date of purchase unless stated otherwise.
Extended warranty
- Labjack: 5 Years
- Atop: 5 Years
- MeanWell: 3 Years
- Teracom: 3 Years
- Novus: 3 Years
