LabJack U3-LV USB Data Acquisition Module

In stock (8 items available)
  • Weight
    0.3 kg
  • SKU
    LAJ-021

The most economical member of the LabJack family, the U3-LV has 16 flexible I/O (digital input, digital output, 12 bit 0 to 3.6 VDC analog input), 2 voltage outputs and USB interface.

Buy more for less:
1-4 items AUD190.27 / each  
5-9 items AUD171.25 / each save 10%
10 or more items AUD161.74 / each save 15%
  • AUD190.27
  • excluding GST

Qty:  
  • The LabJack data acquisition modules are flexible I/O modules for getting signals in to and out from your computer. The family features wide software support with drivers and code examples for a range of platforms and languages. The U3 is the most economical member of the family but it's packed with features.

The LabJack modules come with Windows software that allows you to be quickly up and logging and graphing data.

Flexible I/O:

The first 16 I/O lines (FIO and EIO ports) on the LabJack U3-LV can be individually configured as digital input, digital output, or analog input. In addition, up to 2 of these lines can be configured as timers, and up to 2 of these lines can be configured as counters. On the U3-HV, the first 4 flexible I/O are replaced with dedicated high-voltage analog inputs.

The first 8 flexible I/O lines (FIO0-FIO7) appear on built-in screw terminals. The other 8 flexible I/O lines (EIO0-EIO7) are available on the DB-15 connector on the base of the unit. The optional CB15 board breaks these out to screw terminals.

Analog Inputs:

The LabJack U3 has up to 16 analog inputs available on the flexible I/O lines. Single-ended measurements can be taken of any line compared to ground, or differential measurements can be taken of any line to any other line.

Analog input resolution is 12-bits. The range of single-ended low-voltage analog inputs on the U3-LV is typically 0 to 2.4 V or 0 to 3.6 V, and the range of differential analog inputs is typically ±2.4 V (pseudo bipolar only). For valid measurements, the voltage on every analog input pin, with respect to ground, must be within -0.3 to +3.6 V.

On the U3-HV, the first 4 flexible I/O are replaced with dedicated high-voltage analog inputs. The input range of these channels is ±10 volts or -10 to +20 volts. The remaining 12 flexible I/O are still available as described above, so the U3-HV has 4 high-voltage analog inputs and up to 12 low-voltage analog inputs.

Command/response (software timed) analog input reads typically take 0.6 to 4.0 ms depending on number of channels and communication configuration. Hardware timed input streaming has a maximum rate that varies with resolution from 2.5 ksamples/s at 12-bits to 50 ksamples/s at about 10-bits.

Analog Outputs:

The LabJack U3 has 2 analog outputs (DAC0 and DAC1) that are available on the screw terminals. Each analog output can be set to a voltage between 0 and 5 V with 10-bits of resolution.

The analog outputs are updated in command/response mode, with a typical update time of 0.6 to 4.0 ms depending on communication configuration. The analog outputs have filters with a 3 dB cutoff around 16 Hz, limiting the frequency of output waveform to less than that.

Digital I/O:

The LabJack U3 has up to 20 digital I/O channels. 16 are available from the flexible I/O lines, and 4 dedicated digital I/O (CIO0-CIO3) are available on the DB15 connector. Each digital line can be individually configured as input, output-high, or output-low. The digital I/O use 3.3 volt logic and are 5 V tolerant.

Command/response (software timed) reads/writes typically take 0.6 to 4.0 ms depending on communication configuration. The first 16 digital inputs can also be read in a hardware timed input stream where all 16 inputs count as a single stream channel.

Timers:

Up to 2 flexible I/O lines can be configured as timers. The timers are very flexible, providing options such as PWM output, pulse/period timing, pulse counting, and quadrature input.

Counters:

Up to 2 flexible I/O lines can be configured as 32-bit counters.

I/O Protection:

All I/O lines on the U3 are protected against minor over voltages. The FIO lines can withstand continuous voltages of up to ±10 V, while the EIO/CIO lines withstand continuous voltages of up to ±6 V.

High Channel Count Applications:

By using USB hubs, many LabJacks can be interfaced to a single PC, providing an inexpensive solution for high channel count applications.

16 Flexible I/O each can be configured for:

  • Digital Input: 3.3 or 5 VDC logic level compatible
  • Digital Output: 3.3 VDC
  • Analog Input: 0 to 2.44 VDC or 0 to 3.6 VDC
  • Up to 2 Timers (Pulse Timing, PWM Output, Quadrature Input etc.)
  • Up to 2 Counters (32 bits Each)

Additional Digital I/O: 4

  • Total of 16 analog inputs with 12 bit (4096 level) conversion

Analog Outputs: 2 (10 bit, 0 to 5 VDC)

Supports: SPI, I2C, and Asynchronous Serial Protocols (Master Only). Also Software or Hardware Timed Acquisition

Maximum Input Stream Rate: 2.5 to 50 kHz (Depending on Resolution)

Response Time: Less Than 1 Millisecond

Interface: USB 2.0/1.1 Full Speed

Powered: by USB Cable

Rated for Industrial Temperature Range: -40 to 85 °C

Dimensions: 75 × 115 × 30 mm 

Built-In Screw Terminals for Some Signals

Includes USB Cable and Screwdriver

Drivers Available for Windows, Linux, Mac and Pocket PC

Examples Available for C/C++, VB, LabVIEW, Java, and More

Includes Licensed Copy of DAQFactory Express Software (Win2000+)

Free Firmware Upgrades

Faulty Goods and Warranty

Where such goods have been supplied we undertake to repair or replace them as quickly as possible.Prior to returning faulty items, please contact us with a description of the fault as one of our engineers might be able to assist you by resolving the issue over the phone.
A Warranty form must be filled out and returned with any goods.

Our standard warranty period is 12 months from the date of purchase unless stated otherwise.

Other warranty periods:

Labjack Products: 5 Years
Atop Products: 3 Years
MeanWell Products: 3 Years
Terracom Products: 3 Years

Warranty is subject to us being satisfied that a defect was caused by defective workmanship or materials and was not caused by or was not substantially contributed to by other factors beyond our control including incorrect installation, alterations or modifications of the product not recommended by the manufacturer.

Returns Policy

If you are dissatisfied with our goods you may return them within 14 days of the dispatch date. Contact us for an authorisation and we will refund your purchase less shipping costs and restocking fees. All returned goods MUST be in AS NEW condition including ALL PACKAGING and DOCUMENTATION / MANUALS etc.

Please note:

  • The product returned will attract a 20% restocking fee.
  • The customer must pay the delivery costs.
  • Non standard, custom made or a specially manufactured or imported products are not returnable.
  • Semiconductors, books and software are not refundable

Full Terms and Conditions

By placing an order with Ocean Controls, you agree to be bound by our Terms and Conditions of Trade.

Customers who bought this product also bought

Drop items here to shop
Product has been added to your cart

Related products

Customers who viewed this product bought